Shot Pot™ Timer 21
Shot Pot™ Timer 2Shot Pot Timer 2 with footswitch and nozzle2
Shot Pot™ Timer 2Side view of Shot Pot Timer 23
Shot Pot™ Timer 2Top view of Shot Pot Timer 24
Shot Pot™ Timer 2large pressure sensitive adhesive pillows in Shot Pot Timer5
Shot Pot™ Timer 26
Shot Pot™ Timer 2Cardboard carton flap placed below Shot Pot Timer nozzle7
Shot Pot™ Timer 2Chips of hot melt adhesive being poured into the tank of a Shot Pot Timer.8
Shot Pot™ Timer 2 inside of shot pot timer tank showing the melt grid (Part # CSP016) and lid seal (CSP005).9
Shot Pot™ Timer 2Shot Pot Timer tank filled with hot melt adhesive.10
Shot Pot™ Timer 211
Shot Pot™ Timer 2Shot Pot Timer foot switch assembly (part # CSP214) 12
Shot Pot™ Timer 2 Clearance nozzle to benchtop surface 7”13
Shot Pot™ Timer 2Clearance nozzle to back of machine 7”14
Shot Pot™ Timer 2Free 鶹™ Testing Available15
Shot Pot™ Timer 2Top of Shot Pot Timer Tank with lid seal16
Shot Pot™ Timer 217
Shot Pot™ Timer 2Shot Pot Timer Melt Tank (Part # CSP056)18
Shot Pot™ Timer 219
Shot Pot™ Timer 2filter end cap gluing20

Compatible With:

Most standard .

Product Manuals / Related PDFs:

Manual available - Please call

Shot Pot™ Timer 2

Foot switch activated benchtop hot melt metering system with PID temperature control to apply precise, repeatable hot melt patterns to components moved under the nozzle. The machine should be pressurized with dry air and purged occasionally. PUR is typically removed from cartridges and placed in machine to melt and be applied.

$

Product Videos (Click to View)

Product Details:

  • Complete "Turn-key" bench top hot melt extrusion system.
  • Foot switch with cable to unit to actuate adhesive flow.
  • 3.5 lb. hot melt tank capacity.  Teflon lined.
  • 3 to 5 lb. per hour melt rate depending on adhesive.
  • Removable melt grid in bottom of tank.
  • PID adjustable temperature controller - Readout available in Fahrenheit or Celcius.
  • Pneumatically adjustable adhesive flow control.
  • High Speed valve/module for excellent adhesive shut off.
  • Adjustable timer from .1 to 9 seconds for pre-measured adhesive patterns.
  • Three nozzles and one extra tank seal included with purchase.
  • Typical adhesive viscosities range between 500 and 5000 cps.
  • Typical hot melt used with system are EVA's, APAO's, Polyamides, pressure sensitive and fugitive hot melts.
  • Power requirements are 120VAC or 240VAC, 1200 W
  • Shot Pot/Shot Pot Timer 2 Power Requirements: 120VAC=10 amp/1ph/50-60Hz 240VAC=5 amp/1ph/50-60Hz
  • Dimensions are 18" high x 15" wide x 13.5" deep.
  • Weight is 32.5 lbs.
  • Shot Pot Adapter Threads are 1/4BSPP.
  • Compressed air required: 30-90 psi.
  • Clearance nozzle to benchtop surface 7”Clearance nozzle to back of machine 7”Base can be reversed/ machine will be cantilevered
  • Six month warranty against defective workmanship
  • Method of shipping is UPS.
The Shot Pot Timer™ 2 will increase production speeds dramatically over the manual application of hot melt with hot melt handguns. Both hands are free to move the component requiring precise hot melt dots or lines. Product quality will improve with the Shot Pot Timer™ 2 as precise patterns of hot melt are applied only where needed with no adhesive stringing from the nozzle. Finally, hot melt consumption will be reduced because this machine applies only the quantity of adhesive set by the operator.

QUOTE THIS MACHINERY

Shot Pot™ Timer 2

Call 1-410-761-2727Or Fill Out The Form Below
  • This field is for validation purposes and should be left unchanged.